>_> 45 days in and not paid for emergency SUNDAY well repair jobįuckin bend over backwards to get people water and that's how they re-pay you I usually clean hard palstics with H2O2 ans soft ones with water and finish themk with PJ> TheBear, Petrol jelly Destroy plastic but it is also readily absorbed by many of them. ƬTION looks at past due contractual billings TheBear, cheap toothpaste as polishing compound + a clean rag What, all you electronic guys have to study signals in school, and FFT/DFT/FT is part of those classes on signals Which reminds me, what do you use to "polish" sun-damaged clear plastic, similar to the stuff on pir sensors (both the clear and 'cream' colour ones
![do enola gay smoke fit in 40mm pouches do enola gay smoke fit in 40mm pouches](https://cdn.gorillasurplus.com/images/products/medium/RFIEG-18PNK.jpg)
It looks like you was arc-welding, vs relay contacting The dudes in #math didn't like my questions, because it was about an implementation. I have some questions on the Discrete Fourier Transform. Hyratel really I swear I did it with a screwdriver. If those are relay contacts, they're prbably sintered silver-ZiNīecause the right one looks really arc-scarred Hesperaux, definitively this si not steelĬontacts are hard to say what plating they have, so many mixesĪm i missing something? don't relay contacts by nature have to be magnetic? Maybe the actual contact pads are something else
#Do enola gay smoke fit in 40mm pouches full
Maybe if I let it grow and go full caveman and look like a theBearīird|XXX told me they usually plate with silver but >_> the jailbait seems to want to drip off me It seems to be attracting the wrong ladies ƬTION looks in mirror, woo, time to shaveĪmazing what i find myself working on while I wait for my damn oculus dk2 Practically speaking: TTL inputs require some current to drive, CMOS inputs don't require any just to hold a levelīird|lappy: I see, so CMOS has a capacitative property to it, whereas TTL requires constant current?Īnd practically speaking we just drive ttl and cmos with logic voltagesīird|Lappy: Honestly, I don't know whether or not the TLE h-bridge is CMOS or TTL, but it seems safest to assume TTLīird|Lappy: So, what exactly is CTR? I don't really understand what current transfer is, or what the ratio describes
![do enola gay smoke fit in 40mm pouches do enola gay smoke fit in 40mm pouches](https://www.goldenplazadistributors.com/images/products/large/RFIEG-18PUR_1_.jpg)
bv in my eyesįlynnn, TTL uses bipolar transistors, CMOS uses MOSFETs I don't care what anyone says, you'll always be. The longer time your load power supply will remain available, after source power is cut/turn-off.īird|Lappy: It's a TLE5206-2S h-bridge, but what is the difference between TTL and CMOS?įlynnn: fig 5 on page 8, Current Transfer Ratio is at its highest at around 9-15mA, at which point it would supply up to 13-22mA to the loadĭoes anyone in here have experience with ADS? so for a 17 ms of stable backup power supply time of 12volt supply with 10 ampere (12x10 = 120 watts) load, where input source 12v varies from 12.6v to 8.48v, (rms of 12 is 8.48) then, such psu will need minimum of around: 10amp x 17ms / ( 12.6v - 8.48v ) ~= 41 mF (~= 41000uF) capacitor. a 60 hz supply each Hz (or cycle) is around 17 ms (milli-second) time long. Unhapply this world will be doomed for the time being.īird|Lappy: That I am not sure - what is the difference between the two?įlynnn, what is the part number of the chip, or is it some sort of application-specific IC?įor general power supply related cases C = ( I * dT ) / dV.
![do enola gay smoke fit in 40mm pouches do enola gay smoke fit in 40mm pouches](https://www.tacticaldistributors.co.za/10543-home_default/basic-medium-molle-level-iiia-plate-carriervest-various.jpg)
ƬTION dissapears for bad trolly-trollerbating People will change eventually, but this take time.īird|Lappy: Collector connected to 5v supply, emitter connected to some sort of logic chip input Right along wioth the turds that live thereīest yet border it off and give it back to mexico I long to see the day california does slide off into the ocean and dissapear :)įlynnn, minimum current is desired minimum output current/CTRįlynnn, what is the output of the optocoupler driving? When oh when will idiots stop watching garbage and let hollywood fail and die, as it should have 30 years ago+īird|Lappy: How do I figure out the minimum forward current?įlynnn, you can use a junkbox 2n3904 or 2n2222a with a pretty reasonable base resistor (I'd go for 4.7-6.8k for your situation) and a rather normal LED dropping resistor. Looks like tin but is harder but still bright say on a RF or telecom relay, vs a power relay)
![do enola gay smoke fit in 40mm pouches do enola gay smoke fit in 40mm pouches](http://www.ansgear.com/v/vspfiles/photos/ENOLAPOUCHDEUCETAN-2.jpg)
WilliamWS, small signal contacts use gold If it is silver it is a resonable ammount. Bird|lappy: I see - but that's output, I'm trying to make sure my input doesn't draw more current than my microcontroller can handleīird|lappy, I found one with a thin sheet of copper and to thick plates attached to the coper.